Search:

Type: Posts; User: blackcat4866

Page 1 of 3 1 2 3

Search: Search took 0.11 seconds.

  1. Replies
    0
    Views
    2,390

    Merry Christmas 2020!

    I hope you're all healthy, getting through this pandemic.

    89

    Merry Christmas!
    =^..^=
  2. Replies
    0
    Views
    3,706

    HP DJ T2500MFP 45.2:03 error

    I suppose that I've always known that it's unwise to move a used Designjet, especially up stairs, but now I know exactly why:

    When you tip this little baby up at a 45 degree angle, then carry it...
  3. Replies
    3
    Views
    8,132

    Thank you Dale, for preserving my login! Are...

    Thank you Dale, for preserving my login!

    Are you a copier tech, IT tech, or something else? Amazing how quickly that 9 years passed.

    Did you have to address the hundreds of memberships from...
  4. Replies
    3
    Views
    8,132

    Happy Thanksgiving!

    Uh-oh! It's worse than I thought.

    Well, to anyone reading ... Happy Thanksgiving!
    =^..^=
  5. Replies
    3
    Views
    8,132

    blackcat4866 is back!

    It's been about 13 years since I visited The Copier Network, and I'm happy and sad at the same time.

    I'm happy to see that you're all still here. And I'm sad to see the activity level is nil. I...
  6. Replies
    1
    Views
    898

    I could be more sure if I saw a sample. My best...

    I could be more sure if I saw a sample. My best guess though is that the developer is dead. If so, you'll see the same pattern on the mag roller as you rotate it manually:

    Light areas in a chain...
  7. Replies
    4
    Views
    1,554

    Clear > Interrupt > 0 > Interrupt > 14 > Start. ...

    Clear > Interrupt > 0 > Interrupt > 14 > Start.

    =^..^=
  8. Replies
    4
    Views
    1,817

    I don't know if it's applicable, but I got this...

    I don't know if it's applicable, but I got this error recently on a Falcon III only when duplexing 2-2. It turned out that the connector to the CIS in the DF-700 was poorly mated. =^..^=

    =^..^=
  9. I would change the leading edge sensor. These...

    I would change the leading edge sensor. These sensors are very cheaply made and work poorly at best. I can recall two of these sensors that did not close to 0.5 ohms when brand new in the box.

    It...
  10. Replies
    1
    Views
    1,266

    I totally forgot about this one. Misfeeds (jam...

    I totally forgot about this one.

    Misfeeds (jam code MPFD1_S, MPFD_NM) from the bypass, (jam code MPRD2_N2) from tray #2 only. Flipped corners and skews into the finisher tray. Premature fuser...
  11. Replies
    7
    Views
    2,536

    Let me be the first to tell you: It is...

    Let me be the first to tell you:

    It is unethical to reset or decrement a total counter. How would you feel about buy a machine that someone has turned back the counter? (Like you are trying to.) ...
  12. Replies
    10
    Views
    2,243

    I've had lots of bad experiences with aftermarket...

    I've had lots of bad experiences with aftermarket toner. I can't think of a single good thing to say about it. And by the way, AF350/450 just love to overtoner. It's just the nature of the beast. ...
  13. Replies
    4
    Views
    931

    What a blast from the past! The connector for the...

    What a blast from the past! The connector for the waste toner sensor is just hanging out where the customer can disconnect anytime it for you. After 3 times in one week I had to bill one of our...
  14. Replies
    1
    Views
    1,106

    Laser shutter fault code. Primary corona is not...

    Laser shutter fault code. Primary corona is not seated correctly. Reseat the primary corona unit.

    Laser shutter fault code. Broken wire on the primary corona unit (does not specify charge or grid...
  15. Replies
    1
    Views
    811

    Call it my bias, but I just don't trust...

    Call it my bias, but I just don't trust aftermarket toner. I've had too many bad experiences. =^..^=

    =^..^=
  16. When you get around to adjusting separation, you...

    When you get around to adjusting separation, you must decrease spring tension to increase page separation.

    I know it's counterintuitive. I spent 3 hours pulling my hair out, trying to get 28lb...
  17. Replies
    2
    Views
    1,635

    Horizontal registration home position error. ...

    Horizontal registration home position error.

    The home position sensor may be dirty (filled with toner) or the registration may be unable to shift horizontally. =^..^=

    =^..^=
  18. Replies
    4
    Views
    4,980

    Is it safe to assume that you attempted to zero...

    Is it safe to assume that you attempted to zero out the counter?

    =^..^=
  19. Replies
    4
    Views
    1,236

    My vote is for #3 Hard Drive. The hard drive is...

    My vote is for #3 Hard Drive. The hard drive is only for image memory only so there is nothing special on it. I've pulled the hard drive off a Cougar corpse that was not even the same size and it...
  20. The E065 tells me you're on the right track. It's...

    The E065 tells me you're on the right track. It's possible that you've got a dying composite power supply also. I'd definitely save the expensive item for last resort. =^..^=

    =^..^=
  21. Here are a few possibilities: Misfeeds (jam...

    Here are a few possibilities:

    Misfeeds (jam code 0010, 1000) intermittently on the bed. One page is partly into the fuser. One page is at the registration rollers. Delay at the delivery sensor...
  22. Thread: AR-168D

    by blackcat4866
    Replies
    3
    Views
    1,328

    Were you also planning on doing some maintenance?...

    Were you also planning on doing some maintenance? Drum, blade, developer?

    =^..^=
  23. Replies
    3
    Views
    1,058

    When you say "new" does that mean: 1) used but...

    When you say "new" does that mean:

    1) used but was functioning in the other machine.
    2) used but don't know if it worked in the original machine.
    3) repaired.
    4) or new.

    1) & 4) should...
  24. Replies
    4
    Views
    1,026

    Very common. Install Countermeasure Leaf Spring...

    Very common. Install Countermeasure Leaf Spring (FB6-2734-000) per GTI-T139, as advised by Copyman59.

    =^..^=
  25. Replies
    2
    Views
    1,284

    Bad news! The only way to get the product key is...

    Bad news! The only way to get the product key is to register the product with Sharp and pay the license fee.

    I know, it was already paid for. Well you'll have to pay for it again. You may not have...
Results 1 to 25 of 56
Page 1 of 3 1 2 3