Search:

Type: Posts; User: Luther

Page 1 of 6 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    1
    Views
    1,349

    put the lock back in the hole and turn with a...

    put the lock back in the hole and turn with a screwdriver, there is and arrow on the drum plate to show which way to turn the lock as you turn push drum section and it should go back in
  2. Replies
    1
    Views
    1,748

    replace the charge corona and grid, bizhub 1051...

    replace the charge corona and grid, bizhub 1051 pro correct?
  3. Replies
    12
    Views
    21,233

    well the other solution is to replace the main...

    well the other solution is to replace the main pcb as stated in my other post
  4. Replies
    12
    Views
    21,233

    with power on...wont reset with no power

    with power on...wont reset with no power
  5. Replies
    1
    Views
    1,972

    could be a bad exposure lamp, or the adb board

    could be a bad exposure lamp, or the adb board
  6. Replies
    12
    Views
    21,233

    Product : imageRUNNER 3225 / 3230 / 3235 / 3245...

    Product : imageRUNNER 3225 / 3230 / 3235 / 3245
    Title : Blank Display and Reboots
    Problem :
    The LCD Display is blank, green power light is on and machine keeps rebooting. Checked several DC...
  7. Replies
    12
    Views
    21,233

    mageRUNNER 3225 / 3230 / 3235 / 3235i / ...

    mageRUNNER 3225 / 3230 / 3235 / 3235i / 3245 / 3245i
    Title : Blank Display with Green Light On, ImageRunner will continually reboot.
    Problem :
    Blank Display with Green Light On,...
  8. Thread: ricoh mpc 2500

    by Luther
    Replies
    2
    Views
    4,231

    Thanks that's what I thought and told them,just...

    Thanks that's what I thought and told them,just thought I would check...thanks again
  9. Thread: ricoh mpc 2500

    by Luther
    Replies
    2
    Views
    4,231

    ricoh mpc 2500

    Having a problem with the toner, installed new toner and machine say "independent supplier toner installed" which it always says when using non oem, but under system status it says remaining toner...
  10. Replies
    2
    Views
    6,489

    are you sure the code is 045-316? and not...

    are you sure the code is 045-316? and not 045-361?

    This message was edited by Webmaster on 1-6-10 @ 10:10 AM
  11. Replies
    2
    Views
    1,082

    If your looking for the seperator pad for the...

    If your looking for the seperator pad for the DADFK1 FEEDER.the # is FF6-2455-020
  12. Replies
    2
    Views
    2,060

    This is a common problem with this series, charge...

    This is a common problem with this series, charge corona is arcing either clean it or restring the corona wire,also check to see if you broke a corona wire, hope this helps
  13. Thread: konica F-49-6

    by Luther
    Replies
    3
    Views
    1,172

    The ribbon connection from the scanner to the...

    The ribbon connection from the scanner to the main board is bad, this cable is right on the top of the main board,if you have never taken it apart be careful ,this connection is a common problem,good...
  14. Replies
    1
    Views
    937

    Are you installing a new imaging unit> if you are...

    Are you installing a new imaging unit> if you are just install it and it will reset the indicator and run f8 for you
  15. Replies
    2
    Views
    1,040

    In the 25 mode dip-sw 18 bit 5 is set to 1 set it...

    In the 25 mode dip-sw 18 bit 5 is set to 1 set it to a 0,if it grays it out again something is wrong with the folding option,good luck
  16. Replies
    5
    Views
    1,200

    I think its the laser also, happpens in prints...

    I think its the laser also, happpens in prints and copies,if it were the dv unit i really dont think they would be evenly spaced,and happening in prints also illiminates the scanner
  17. Replies
    1
    Views
    1,792

    Thats a counterfit code, someone tried to copy...

    Thats a counterfit code, someone tried to copy currency and more the once, minolta has to be notified to reset the code the treasury dept is more then likely going to be notified,hope this helps
  18. Thread: Konoca 7030

    by Luther
    Replies
    1
    Views
    1,013

    F51-5 is main motor failure, i would check to see...

    F51-5 is main motor failure, i would check to see if ,something is bound, fuser, drum unit, etc.check the seals at the ends of the drum they come off and bind the drive unit, hope this helps
  19. Replies
    2
    Views
    1,483

    The fuser heater is staying on too long, check or...

    The fuser heater is staying on too long, check or replace the thermistors, or could be a bad solid state relay,i would replace the upper fuser section, good luck
  20. Thread: CANON IR 1600

    by Luther
    Replies
    1
    Views
    970

    Giving the error code would help

    Giving the error code would help
  21. Replies
    0
    Views
    765

    I just replaced the drum and developer and i need...

    I just replaced the drum and developer and i need to reset the wrench indicator and run f8, if anyone has the procedure or a copy of the service manual it would be greatly appreciated !
  22. Replies
    2
    Views
    1,460

    You need to have the chip reset on the drum units...

    You need to have the chip reset on the drum units to turn the indicator light off, this can not be done by resetting a counter
  23. Replies
    2
    Views
    1,257

    Did you use the grease that comes with the...

    Did you use the grease that comes with the sleeve? if you did you used to much of it and it causes a thermal break and causes fuser errors,clean the grease off and apply a smaller amount ,this should...
  24. Thread: Konica 9028

    by Luther
    Replies
    1
    Views
    1,184

    Hi f28-1 is a shorting or broken charge corona,i...

    Hi f28-1 is a shorting or broken charge corona,i wouldnt touch any "reset" butoon on the board,good luck
  25. Replies
    1
    Views
    968

    It is not a fuse it is a chip and it needs to be...

    It is not a fuse it is a chip and it needs to be reset, there are companies that do it or you can purchase a resetter but they are pretty pricey, hope this helps
Results 1 to 25 of 139
Page 1 of 6 1 2 3 4