Search:

Type: Posts; User: Nasher

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Thread: Ricoh MP161spf

    by Nasher
    Replies
    2
    Views
    2,296

    turn on sub paper size to auto and change auto...

    turn on sub paper size to auto and change auto continue to immediate
  2. Replies
    1
    Views
    1,875

    try sending the jobs in 1200 dpi in driver...

    try sending the jobs in 1200 dpi in driver normally the blacks are good on these printers please check that the text is blk and not cmy
  3. Replies
    4
    Views
    3,660

    could be pump as above post also try cleaning out...

    could be pump as above post also try cleaning out the black toner pump pipe or make sure if the copier has a paper bank that the lover right door is set at the rear the sp for the message is sp5-051
  4. Replies
    1
    Views
    1,775

    if the copier has a bridge unit i would change...

    if the copier has a bridge unit i would change the 2 micro swt on unit for the power on jams and also upgrade firmware for power on jams as this changes the time for the detection of the 2 swt in...
  5. Replies
    1
    Views
    2,812

    disconect the H/D and power the machine up if it...

    disconect the H/D and power the machine up if it works formatte the hardrive via an external caddy it takes about 30 mins to do and it should work ok after its re fitted you will need to re input the...
  6. Replies
    3
    Views
    1,070

    Are they small squares to do with the laser setup...

    Are they small squares to do with the laser setup most faults like this are down to the cleaning unit drive assberly it has been moded and comes as a complete unit
  7. Replies
    4
    Views
    3,812

    I have also had tis problem and in the end got...

    I have also had tis problem and in the end got m/c working. I had a mp5500 with about 300k on the clock then it started with sc220 changed detecton board and service full pm parts still no good but...
  8. Replies
    4
    Views
    2,646

    YOU WILL NEED A NETWOK KIT THE rj 45 IS ONLY...

    YOU WILL NEED A NETWOK KIT THE rj 45 IS ONLY THERE BECAUSE ITS ON THE GROUNDWORKS BOARD
  9. Replies
    5
    Views
    1,437

    Try lifting the left corner of the scanner the...

    Try lifting the left corner of the scanner the same fault you get on a 1035
  10. Replies
    2
    Views
    1,002

    there are some earth tabs under the tray and at...

    there are some earth tabs under the tray and at the reae of the cassette make sure they are touching the main body when tray is in
  11. Replies
    2
    Views
    1,430

    To get into Special SP (CA 107 C hold # and copy...

    To get into Special SP (CA 107 C hold # and copy SP) Hold down the up and down arrow keys together for 5 seconds let go and press the escape key for 5 seconds (it will go into SSP when you release...
  12. Replies
    7
    Views
    1,866

    had a citrix problem on a mp4500 not mpc it kept...

    had a citrix problem on a mp4500 not mpc it kept showing a message on the user pc we tried all pcl and rpcs drivers in the end we used the mini driver and it works great see if mini drivers are...
  13. Replies
    1
    Views
    720

    turn on fuser ideal in sp mods

    turn on fuser ideal in sp mods
  14. Replies
    17
    Views
    3,180

    these are rare things in these m/c we had one in...

    these are rare things in these m/c we had one in our office with a netwokcard in it
    the only way to change the ip address on the card is to use the ARP comand or use telnet the ARp is the easy one...
  15. Replies
    3
    Views
    1,517

    The odd thing about these m/c is that when the...

    The odd thing about these m/c is that when the reg clutch starts to play up it will jam on duplex only change the reg clutch good luck
  16. Replies
    3
    Views
    1,133

    I have seen this i think a few times what the...

    I have seen this i think a few times what the customer will do is put the originals on the d/f and as it has lifted gives it the old little jiggle to make sure the copies are in ok this then confuses...
  17. Replies
    3
    Views
    972

    Try removing the end cover on the dev unit (the...

    Try removing the end cover on the dev unit (the end that the toner gose in) clean all the dev and toner out of the 2 gears as they can make the paddle roller hard to turn so you get poor cross mixing
  18. Replies
    3
    Views
    4,158

    There is a sensor down at the rear of the m/c...

    There is a sensor down at the rear of the m/c where the toner comes out of the transfer unit it will need to be removed and cleaned as it will be dusty (not toner)we have had this on the 2051 also at...
  19. Replies
    4
    Views
    1,174

    iF YOU SELECT SCANNER YOU CAN SELECT STORE ONLY...

    iF YOU SELECT SCANNER YOU CAN SELECT STORE ONLY THEN WEB BROWSE TO THE DOC SERVER THERE YOU WILL SEE YOUR DOCK OOPEN IT UP THEN SAVE IT TO YOUR PC NO SOFTWARE REQ IF YOU TRY TO DO IT VIA THE DOC...
  20. Replies
    14
    Views
    5,057

    had a 1224 do the same on me then i found that PC...

    had a 1224 do the same on me then i found that PC controle was turned on in the user cod set up but there were no user cods setup
  21. Thread: sc 402

    by Nasher
    Replies
    4
    Views
    1,182

    check the drum earth at the rear of the copier or...

    check the drum earth at the rear of the copier or put a meter prob on it then to earth and run some copies is it runsok take out the shaft etc and clean it
  22. Replies
    1
    Views
    868

    at the rear of the sortet on the side that...

    at the rear of the sortet on the side that contacts the main m/c there is a small black sen arm about half way down it sticck out about 1/2cm it ften gets brocken off givng door open etc
  23. Replies
    6
    Views
    1,237

    You may find that the rear bracket that the df...

    You may find that the rear bracket that the df scews onto is slightly bent down and as you lower the df it will make and brake the sensor on the bracket all you need to do is pull it up slightly
  24. Replies
    9
    Views
    1,860

    Hiperry i too have seen this on a few m/c and the...

    Hiperry i too have seen this on a few m/c and the best solution is to change the drum unit as one lump as the problem will keep coming back we do this only on the ones that we have a problem...
  25. Thread: NASHUATEC C 503

    by Nasher
    Replies
    1
    Views
    1,161

    its the revolver hp sen code have you had the...

    its the revolver hp sen code have you had the revoler out ifso it may not be set in correctly or the sen wich is at the front of the revoler may be dirty remove the unit and give it a good vac then...
Results 1 to 25 of 48
Page 1 of 2 1 2