Search:

Type: Posts; User: mrfuser

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    0
    Views
    992

    Mpc5501 first page grey line

    I have an mpc5501 at a client that is causing a wide grey line on the first page printed or copied. The rest in a job come out fine just the first is a problem. Have you seen this?
  2. Thread: Mpc5501 j017 ?

    by mrfuser
    Replies
    1
    Views
    3,786

    Mpc5501 j017 ?

    Anyone have a clue what is causing random J017 on the MPC5501? Bad clutch? Sensor? All check out okay in service mode.

    Thanks for any tips all!

    K
  3. Replies
    1
    Views
    10,234

    Figured it out, kept missing one service mode.

    Figured it out, kept missing one service mode.
  4. Replies
    1
    Views
    10,234

    MPC5501 Remove Fiery ?

    Client wants to remove the fiery, which we physically did, and thought we did all the adjustments in service mode, yet the internal controller is still not working.

    Any ideas?


    Thanks

    K
  5. Replies
    0
    Views
    6,515

    xerox 5330 bad copy, good print, please read

    We have good print quality but bad copy quality from glass or feeder. Cleaned all optics and still poor quality. Any ideas?

    Thanks

    65
  6. Replies
    1
    Views
    2,331

    GPR-9 Toner Needed

    Anyone have a decent source for GPR-9 toner?

    Thanks

    KC
  7. Replies
    0
    Views
    1,577

    7022 bypass plug for key counter

    Anyone have a part number for this?
    It is a small black plug with a single looped wire that plugs into the harness on front upper right of copier behind corner cover.
  8. Replies
    0
    Views
    1,865

    Konica 7022 F-41-1

    We have a client with a couple of old Konica 7022 units. One has an F-41-1 on it. Seems like a blown fuse somewhere not powering scanner assembly. Any idea where the fuse may be hiding for this? ...
  9. Replies
    0
    Views
    1,872

    irAdvanced C5045 Magenta Stripe

    60
    Got a C5405 that is causing a magenta stripe on the op side as paper exits. Replaced drum, cleaned entire inside and stripe remains. I do see the stripe on the ITB Transfer roller on the door...
  10. Replies
    0
    Views
    2,976

    C5045 bushing black dv

    Does anyone know if you can order the bushing for the black developer unit drive on the c5045?
  11. Replies
    0
    Views
    3,373

    phaser 7760 please wait warming up

    Okay, machine can print just fine from service mode, but when try to boot normally it just says "please wait warming up" and never goes to ready. No error codes generated and all tests in service...
  12. Replies
    0
    Views
    1,868

    Bizhub 223 hard drive

    Client had previous company add a hard drive but machine does not recognize it. Must we turn on in tech mode?

    Thanks
  13. Thread: C451 false jam

    by mrfuser
    Replies
    0
    Views
    1,369

    C451 false jam

    Machine shows on panel a jam behind right door at very bottom. There is no jam and we have replaced all sensors we can find and entire transfer assembly on door for good measure. Jam persists .
    ...
  14. Replies
    0
    Views
    1,234

    Mp3350 scan to copy problem

    Went there and found that it is non op side edge of page that is light on letter size when using adf and op side when lay on glass.

    strange thing is if we scan to email the document is fine. Only...
  15. Thread: 2238c SC440-01

    by mrfuser
    Replies
    0
    Views
    2,647

    2238c SC440-01

    Replaced, K Drum motor, K Pcu, cleaned waste augers and it still pops the code. If we put in a new drum it runs for a bit saying it is adding toner then stops and goes into SC440-01 code.

    Any...
  16. Replies
    1
    Views
    2,696

    xerox 5655 swipe card ?

    Client just purchased this machine and it works fine, but when we try to go into admin it says SWIPE CARD and in the upper right it says KEYBOARD ACCESS. Is there a way around this to shut it off? ...
  17. Replies
    2
    Views
    3,459

    Cretan? But of course!

    Cretan? But of course!
  18. Replies
    0
    Views
    1,212

    C350 No paper lift tray 3

    machine recognizes tray 3 is inserted in tech mode, just has paper empty flag showing. No lift of paper. We replaced the cassette, paper lift motor, board for paper drawer, feed head, still no...
  19. Replies
    0
    Views
    962

    C351 multi page pdf issues

    We do not set the machine to "seperate scan", yet it still sends seperate scans to email.

    Any idea why?


    Thanks

    Kelly
  20. Replies
    2
    Views
    1,669

    Why are you hacking my thread to ask for a...

    Why are you hacking my thread to ask for a service manual? Someone delete this guy!
  21. Bizhub c451 Wrinkling Last 1/3 of page as exits on LETTER

    Legal, ledger are just fine, letter R most of the time is okay. Letter is bad everytime except once in a great while it will pass a good page.

    Swapped fusers, same problem. Cleaned rollers,...
  22. Replies
    0
    Views
    1,914

    Ricoh Priport HQ7000 Jam under Drum Unit

    Machine was working fine, then suddenly started jamming. We find paper under drum unit at bottom of machine. Any idea what has failed? We normally work on Riso and have not seen this before.
    ...
  23. Replies
    1
    Views
    1,450

    C351 Duplex Jams, Simplex Fine

    Machine was working great, then client reports it just started duplex jamming. Is there a clutch to look for in these that I should take with me? Client is 40 miles away, so any input before going...
  24. Replies
    2
    Views
    1,669

    We can take Fuser out and it turns fine, all...

    We can take Fuser out and it turns fine, all gears inside look
    fine, but when installed it makes loud clacking sound like
    gears are missing teeth. Paper stops going into Fuser so
    obviously...
  25. Replies
    0
    Views
    1,193

    Does anyone know of any company doing fuser...

    Does anyone know of any company doing fuser rebuilds on the C350/351/250 series? Seems such a waste to keep tossing these entire units when only one roller goes bad.

    Any thoughts?

    Thanks
    ...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4