Search:

Type: Posts; User: rjonese

Page 1 of 8 1 2 3 4

Search: Search took 0.10 seconds.

  1. Thread: e studio 45

    by rjonese
    Replies
    2
    Views
    2,257

    check cmos battery? im guessing

    check cmos battery? im guessing
  2. Thread: toshiba 352

    by rjonese
    Replies
    2
    Views
    2,216

    replace the plastic thing that presses on the...

    replace the plastic thing that presses on the corona wire to stop it from vibrating

    6LE76317000

    This message was edited by rjonese on 9-26-11 @ 11:54 AM
  3. Thread: E studio 200

    by rjonese
    Replies
    2
    Views
    1,530

    Poor copies so i changed the process unit with...

    Poor copies so i changed the process unit with new one.
    (pu1610s) then reset all counters....1-2 weeks later
    grinding noise.... replaced pu unit (over full of toner
    .. so full mix auger wont...
  4. what level of firmware? and 673 dont work on a...

    what level of firmware?

    and 673 dont work on a es 20

    reset 401
    and 251
  5. Replies
    1
    Views
    5,421

    toner does not end when it asks for toner.... 25...

    toner does not end when it asks for toner.... 25 percent left... wait until message says "Replace toner now" and machine stops copying... then they are empty
  6. Thread: SHARP AR-507

    by rjonese
    Replies
    1
    Views
    1,321

    cut from manual "U7 00 Content RIC communication...

    cut from manual
    "U7 00 Content RIC communication trouble
    Detail Communication error with RIC
    Error in communication line test after
    turning on the power or exiting from SIM.
    Cause Improper...
  7. Replies
    2
    Views
    1,014

    not sure why you couldnt look it up yourself......

    not sure why you couldnt look it up yourself... but precision roller 's web site lists same uhr for both so yes i would say they are the same
  8. Replies
    2
    Views
    1,202

    hows the rest of the pm drum worn out? fuser...

    hows the rest of the pm drum worn out? fuser caked up? do a full pm and get back to us. a cleaning blade by itself dont fix much
  9. Replies
    6
    Views
    1,413

    are the lines there when u do a test print or...

    are the lines there when u do a test print or copy only?
  10. Thread: Studio 35

    by rjonese
    Replies
    3
    Views
    1,290

    did u meter the dev bias at the mag roller while...

    did u meter the dev bias at the mag roller while running copies? make sure the metal tab on the dev unit is touching the mag roller. is the dev bias metal tab under the dev unit (in copier) clean...
  11. Thread: MX 2700 E7-11

    by rjonese
    Replies
    3
    Views
    3,482

    canned ? step one to u have manual... have u...

    canned ? step one to u have manual... have u checked fuses? do u have voltages at the invertor board? is ribbon cable good to inverter board? have u replaced lamp and inverter board?

    This...
  12. Thread: Grease

    by rjonese
    Replies
    2
    Views
    3,606

    is the same barierta grease as ricohs use if that...

    is the same barierta grease as ricohs use if that helps
  13. Replies
    4
    Views
    1,462

    take rollers off shaft..... use fine sand paper...

    take rollers off shaft..... use fine sand paper or scotch brite to scuff steel shaft ..clean the one way clutches with alint free towel and alcohol lube clutch with one drop of oil reassemble....by...
  14. Thread: AR450

    by rjonese
    Replies
    2
    Views
    1,173

    jjust adding nic to a u model wont work u need...

    jjust adding nic to a u model wont work u need the kit as was said
  15. Thread: sharp ar-m450n

    by rjonese
    Replies
    1
    Views
    905

    sure would be nice to know what the error was.....

    sure would be nice to know what the error was.....
  16. Replies
    1
    Views
    1,993

    not same problem as u but had some random reboot...

    not same problem as u but had some random reboot problems with one of these (336) turned out to be a faulty hdd (no errors reporting bad hdd) only one problem generic hdd wont work u need one from...
  17. its a big job .... u just have to tear it down...

    its a big job .... u just have to tear it down completely .laser is accessed from the top .... good luck. by the way manuals not much use, i looked it up b4 i posted. if u need manual pm me yer...
  18. Replies
    2
    Views
    1,950

    on toshibas you can only change one board at a...

    on toshibas you can only change one board at a time (except system logic) if you changed the scanner board and the sys board at same time you have bad problems.... i dont know if its repairable. we...
  19. Replies
    1
    Views
    1,572

    hows the pm? are drums recent? dev? cundctive...

    hows the pm? are drums recent? dev? cundctive grease on all grounds locate don teh drums?

    more info pls
  20. Replies
    1
    Views
    1,568

    sorry your english is too poor to understand. ...

    sorry your english is too poor to understand.

    do you mean the colors are not natural?
    do the colours "line" up?
    have you looked in the owners manual to find the calibration proceedure?

    sorry...
  21. Replies
    2
    Views
    1,776

    exactly ... however the best thing for these is...

    exactly ... however the best thing for these is not so much the mods but using 281c colour dev ... cuts down on the dusting by half.... also never push the limits of the pm cycle ... these were a bit...
  22. Replies
    2
    Views
    975

    did you go check in printer properties if the...

    did you go check in printer properties if the finisher is installed as an option in the driver?... you have to set the options as these old machines dont auto update (or if they do they require the...
  23. Replies
    2
    Views
    1,901

    did you get it solved?

    did you get it solved?
  24. Thread: estudio 35

    by rjonese
    Replies
    6
    Views
    1,257

    no didnt upgrade browser Gonna replace the HDD...

    no didnt upgrade browser

    Gonna replace the HDD on the controller and reload the firmware i will let you know
  25. Thread: estudio 35

    by rjonese
    Replies
    6
    Views
    1,257

    disk type :note it WAS working for over a year.....

    disk type :note it WAS working for over a year.. it just quit all by itself.

    This message was edited by rjonese on 3-13-09 @ 2:42 PM
Results 1 to 25 of 184
Page 1 of 8 1 2 3 4