Search:

Type: Posts; User: Ricky965

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds; generated 7 minute(s) ago.

  1. Replies
    2
    Views
    1,624

    I don't need it now. I was able to get it from my...

    I don't need it now. I was able to get it from my Kyocera site. Thanks
  2. Replies
    2
    Views
    1,624

    Kyocera Ecosys M2540dw service manual

    Anyone have a copy of Kyocera ecosys M2450 service manual?
  3. Replies
    0
    Views
    907

    Kyocera M2540DW firmware

    Have a machine that will FAX, but sometimes will give a F375 error, a 33C error and a F245 error.
    Anyone have any other ideas or the firmware? Thanks
  4. Replies
    0
    Views
    1,366

    Kyocera Ecosys M2540dw Error F330

    Copier will print status, menu map etc. But when you go to copy, the paper feeds and it doesn't begin to feed paper but gives error F33C

    I mistyped the code in the post header. I went and pulled...
  5. You have a bad developer. Seen it many times....

    You have a bad developer. Seen it many times. Looking at a ecosys 2535 that does it right now. Had one last week.
  6. Replies
    1
    Views
    1,866

    Okidata MC361 firmware

    I have a Okidata MC361 in the shop. It has paper feed problems from the bottom tray. I have tried rollers, drawers etc. Works flawlessly through the bypass. Made 400 copies without jam through the MP...
  7. Replies
    1
    Views
    1,137

    Kyocera M2535dn firmware

    The USB drive slot doesn't work, so can't update the firmware. Must be problems on the main board.

    I have the firmware, it was on my other PC, just can't reload it. Thanks for looking at it.
  8. Replies
    1
    Views
    1,137

    Kyocera M2535dn firmware

    I have a customers Kyocera in the shop that lost the FAX capability. It doesn't select. Tried a new card under warranty and it didn't find it either.
    Tried service mode and there are no FAX...
  9. Replies
    0
    Views
    679

    Customers machine has an Alarm light. Then a...

    Customers machine has an Alarm light. Then a message about "Supply Rec. Paper Tray 1". Paper tray is full. However when trying to feed through the bypass it sounds like it is locked up. Any...
  10. Replies
    1
    Views
    819

    How do I initialize the developer after I replace...

    How do I initialize the developer after I replace it, and are there any other problems That I might be overlooking on this analog machine?
  11. Replies
    3
    Views
    1,124

    What is it and what's most likely the problem? I...

    What is it and what's most likely the problem? I don't have this particular service manual
  12. Replies
    1
    Views
    1,059

    Contact Carolina Wholesale. There is some...

    Contact Carolina Wholesale. There is some training involved and testing.
  13. Replies
    1
    Views
    1,025

    I don't have the service manual for this model. ...

    I don't have the service manual for this model. I need to replace the paper feed roller. Is this an easy job? I've heard from parts rep that these things are flying out of their stores.
  14. Replies
    2
    Views
    826

    Thanks for your answer. I knew that the thin...

    Thanks for your answer. I knew that the thin side had caused the previous roller to contact the thermostat and rub the film off. However, after mic'ing the new roller shaft and the old there was a...
  15. Replies
    2
    Views
    826

    One end of the fuser bearing is thicker than than...

    One end of the fuser bearing is thicker than than the other, possibly to keep the roller away from the thermostat. Which side goes toward the thermostat, thick or thin. I don't have a manual for...
  16. Replies
    2
    Views
    1,131

    Have a Mita KM3530 that will make normal copies...

    Have a Mita KM3530 that will make normal copies and suddenly changes to all black copies with no text visible. Is this the Laser going bad or what?
  17. Replies
    1
    Views
    711

    We located it. No problem.

    We located it. No problem.
  18. Replies
    1
    Views
    711

    Where is it located and what is the part number.

    Where is it located and what is the part number.
  19. Replies
    10
    Views
    2,765

    I've seen Doctor blades mis-adjusted and they...

    I've seen Doctor blades mis-adjusted and they would let too much toner over the top and slip through, dumping on the ends of the corona wire. I'd guage it with Paper shims to be sure.
  20. Replies
    1
    Views
    1,469

    I want to disconnect the sorter from the main...

    I want to disconnect the sorter from the main unit and disable the sorter while I repair the copier.

    What is the correct procedure to enter service mode and then disable the sorter?
  21. Replies
    2
    Views
    1,190

    We found the problem after a while. Finally...

    We found the problem after a while.
    Finally determined the paper wasn't going through the fuser in the center but over on the edge. Looking further led to a broken part in the paper tray. ...
  22. Replies
    2
    Views
    1,190

    We recently did Maintenance on this KM3530 Mita,...

    We recently did Maintenance on this KM3530 Mita, replacing many parts. New fuser, New transfer Roller and new Exit Rollers with shafts. Occ*ssionally it still jams at entrance of Paper Exit...
  23. Replies
    1
    Views
    903

    Have a Xerox XD130df in the shop. works ok for a...

    Have a Xerox XD130df in the shop. works ok for a while, then casts toner below
  24. Replies
    5
    Views
    1,051

    Thanks for the additional info. I had manual on...

    Thanks for the additional info. I had manual on Ricoh Ft 5840 but not the sorter unit. I plan on going over to check it next week. Thanks Derek
  25. Replies
    5
    Views
    1,051

    Actually I'm not sure. It's a Savin 900D. I...

    Actually I'm not sure. It's a Savin 900D. I believe it is a ST26 sorter. The paper doesn't finish exiting the fuser and the error is Paper path. Can I remove the sorter *ssembly on this and then...
Results 1 to 25 of 57
Page 1 of 3 1 2 3