Search:

Type: Posts; User: TOSH-EUROPE

Search: Search took 0.00 seconds.

  1. Replies
    14
    Views
    5,726

    Hi Bryan, there exists a little utility that...

    Hi Bryan,

    there exists a little utility that makes the download properly.

    I can send to you if you like.

    Regards,
  2. Replies
    7
    Views
    2,850

    Hi, beside of all the mechanical modifications...

    Hi,

    beside of all the mechanical modifications you can also try to select 6 ppm as colour speed instead of 11 ppm. The code is: 08-497=1

    Regards,
  3. Replies
    10
    Views
    7,244

    Hi, take a look at Products & Services -...

    Hi,

    take a look at Products & Services - Copiers

    From 23ppm to 85ppm they have a common architecture, same user interface (touch panel) and easy to use printer drivers.

    Scan functions are...
  4. Replies
    1
    Views
    1,120

    Hi, is a network card installed? If YES, do...

    Hi,

    is a network card installed? If YES, do you get any setting list printer after power on?

    The NIC has a jumper that defaults it's settings. I believe it is JP2 and should be marked with...
  5. Replies
    2
    Views
    2,224

    Hi, in case of DP-2460 there were 2 options...

    Hi,

    in case of DP-2460 there were 2 options available:

    a) KR-7006, GDI interface ==> NOT SUPPORTED
    b) SC-1 controller ==> NOT SUPPORTED but you can try HP-5SI PCL5/5e printer driver

    In case...
  6. Replies
    6
    Views
    3,115

    Hi, the software is called FSMS and latest...

    Hi,

    the software is called FSMS and latest version is 4.2.0. You can download the firmware through serial interface.

    In addition there is a possibility to use a ftp application to do it in a...
  7. The very latest printer drivers for the e-BRIDGE...

    The very latest printer drivers for the e-BRIDGE based products can be downloaded from:

    Printer Driver Portal
  8. Hi, the PRINTER/NETWORK button with the Admin...

    Hi,

    the PRINTER/NETWORK button with the Admin area should help you further. If the config page is printed after power on you can use IE to configure the board. Default p*ssword is "sysadm".
    ...
  9. Replies
    4
    Views
    2,571

    Hi, now with the e-STUDIO170F on board and the...

    Hi,

    now with the e-STUDIO170F on board and the fact, that most laptops don't have parallel anymore, TOSHIBA is launching in AUG'05 a SUB/PARALLEL converter.

    It is not a standard device because...
  10. Replies
    5
    Views
    1,559

    Hi, very recently TOSHIBA has released V1.47AT...

    Hi,

    very recently TOSHIBA has released V1.47AT for the printer board GA-1031 just to fix this problem.

    Let me know if you can't get it and I'll provide to you.

    Regards,
  11. Replies
    2
    Views
    1,953

    Hi, I'm not shure if your problems still valid...

    Hi,

    I'm not shure if your problems still valid because of 1/2 year delay.

    All below is valid for the e-BRIDGE based models (eS230/280/350/450/3511/4511):

    In general TOSHIBA released system...
  12. Replies
    14
    Views
    5,726

    Hi, the GA-1040 (EFI product) comes standard...

    Hi,

    the GA-1040 (EFI product) comes standard with PCL6 only. You could add diskless or disk PS (real Adobe)option. All enabled options are on the setting list.

    Latest version is 1.3. I can...
  13. Replies
    6
    Views
    2,703

    Do you have the SC-1 controller beside the copier...

    Do you have the SC-1 controller beside the copier of the embedded printer board KR-7009?

    Each of it should print a setting list.

    The embedded printer board with a NIC (which was an option as...
  14. Replies
    3
    Views
    1,716

    Hi, can be fixed by a) IC112 chip or b)...

    Hi,

    can be fixed by

    a) IC112 chip or
    b) new MCU board.

    Regards,
  15. Replies
    3
    Views
    1,935

    Hi, this is a problem with XP SP2 only....

    Hi,

    this is a problem with XP SP2 only. TOSHIBA released a fix and it was, as far as I remember, part of the system software SYS300. Latest version is SYS320.

    Regards,
  16. Replies
    4
    Views
    3,676

    Hi, a) I have seen this problem with the...

    Hi,

    a) I have seen this problem with the eS-210c in case, that the duplex unit was not properly fitted.

    You can take off the ADU and power on the copier. If it is the ADU the Fiery RIP will go...
Results 1 to 16 of 16