Search:

Type: Posts; User: johnbla

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    4,040

    Try replacing the HL pwb.. a known issue

    Try replacing the HL pwb.. a known issue
  2. Thread: AM-400

    by johnbla
    Replies
    2
    Views
    709

    SharpUK does have full manuals for this...

    SharpUK does have full manuals for this machine.... look in 'Personal Products' for non-Business class machines...

    P/n MLEVP2402XHSA--AG--Release Lever

    Regards

    Johnbla
    ...
  3. Replies
    1
    Views
    610

    Where is the Dev spilling from ? The Dev is...

    Where is the Dev spilling from ?

    The Dev is contained in a separate section within the Toner cartridge.

    Did you replace the whole Drum Unit or just the Drum ?

    Regards

    Johnbla
  4. Replies
    3
    Views
    1,062

    Try this link ...

    Try this link

    http://www.sharpusa.com/files/fax_man_ux510.pdf

    Regards

    Johnbla

    http://www.copierforum.co.uk
  5. Replies
    2
    Views
    841

    E7-02 is laser trouble... check the connections...

    E7-02 is laser trouble... check the connections to the LSU

    Regards

    Johnbla

    http://www.copierforum.co.uk
  6. Replies
    2
    Views
    774

    check the Sharp Tech bulletins, there is a new...

    check the Sharp Tech bulletins, there is a new cleaning kit for them

    Regards

    Johnbla

    http://www.copierforum.co.uk
  7. Thread: ar-m205 sim

    by johnbla
    Replies
    1
    Views
    687

    Sim 42-01 to clear Dev count and Yes 24-07 for...

    Sim 42-01 to clear Dev count and Yes 24-07 for Drum count reset

    Regards

    Johnbla

    http://www.copierforum.co.uk
  8. Replies
    1
    Views
    790

    Where did you remove the Jam from ? There are...

    Where did you remove the Jam from ?

    There are only 3 paperpath sensors on the machine,and paper empty sensors in each tray PUP

    1. at the start of the paper path, just below the PS roller.......
  9. Replies
    1
    Views
    694

    Clean the ProCon sensors on the drum housing and...

    Clean the ProCon sensors on the drum housing and run Sim 44-02

    Regards

    Johnbla

    http://www.copierforum.co.uk
  10. Replies
    1
    Views
    860

    Assume that you have SIM 14 clear ? Replace...

    Assume that you have SIM 14 clear ?
    Replace thermistors in F section

    Regards

    Johnbla

    http://www.copierforum.co.uk
  11. Replies
    4
    Views
    704

    Mike you on the TC board? Drop me a PM ...

    Mike
    you on the TC board?
    Drop me a PM

    Regards

    Johnbla

    http://www.copierforum.co.uk
  12. Thread: ARP350

    by johnbla
    Replies
    2
    Views
    877

    Try looking to see if the TC spring...

    Try looking to see if the TC spring [MSPRP1550FCZZ] (ARM350 PG Section 3)missing from the PS Roller Unit.

    Regards

    Johnbla

    http://www.copierforum.co.uk
  13. Thread: AR-161

    by johnbla
    Replies
    1
    Views
    710

    Yes 160k is relatively high, depends on age and...

    Yes 160k is relatively high, depends on age and daily through put, but given a GOOD service, in a 'home' environment, it should serve well

    Regards

    Johnbla

    http://www.copierforum.co.uk
  14. Replies
    5
    Views
    1,361

    The only problem with the 25~1 method I found,...

    The only problem with the 25~1 method I found, was that it tended to pop the Drum Toner Seal, the thin plastic distorted with all the Toner going through the WT auger.

    Regards

    Johnbla
    ...
  15. Replies
    5
    Views
    1,361

    Yes 1. Remove Toner motor drive gear from the...

    Yes
    1. Remove Toner motor drive gear from the rear of the Toner hopper
    2. Good clean internal [DM sensors etc]
    3. Check Toner concentration Sim 25-01[will be below 30]
    4. keep doing 'sky shots',...
  16. Replies
    3
    Views
    826

    Okay lets start again.......... Go to Sim...

    Okay lets start again..........

    Go to Sim 22-12, this will give you the Drum counter... it should read 000 or near.
    If not then go to Sim 24-07, while '000' blinking select 1 from the key pad,...
  17. Replies
    3
    Views
    826

    After you get to 24-7 and the flashing 000, hit...

    After you get to 24-7 and the flashing 000, hit 'Start' and then 'Start' to be sure and turn the machine off and then back on.... the drum light should clear.

    Caution......... do not flick the...
  18. Replies
    10
    Views
    2,598

    Sorry my mistake... Go back into Sim 27 ~ 01 and...

    Sorry my mistake...
    Go back into Sim 27 ~ 01 and set to it's original setting.
    Go into Sim 26 ~ 01 and subtract 10 from the number displayed [ i.e. if 15 displayed, change it to 05 ]
    and ...
  19. Thread: AR 336

    by johnbla
    Replies
    7
    Views
    1,085

    No Regards Johnbla ...

    No

    Regards

    Johnbla

    http://www.copierforum.co.uk
  20. Replies
    10
    Views
    2,598

    Switch the machine OFF and Un-plug power cable,...

    Switch the machine OFF and Un-plug power cable, then remove the Sorter connector from the rear of the machine.

    Power up and press the following... Clear ~ Pause ~ Zero ~ Pause .... as the machine...
  21. Thread: sharp AR-205

    by johnbla
    Replies
    5
    Views
    1,004

    Tom best guess, it will probably be the Fuser...

    Tom
    best guess, it will probably be the Fuser exit sensor, it gets cooked and fails.

    Because it is dual'd to one connector with the Exit sensor, it is a pain to replace.

    Suggest cut and solder...
  22. Thread: AR 336

    by johnbla
    Replies
    7
    Views
    1,085

    Make sure you are in Copy mode Then Program ~...

    Make sure you are in Copy mode
    Then Program ~ Interupt ~ Cancel ~ Interupt, 22 ~ Start, 1 ~ Start....

    Will open the Counter display in Engineering mode

    CA to return to normal display
    ...
  23. Thread: sharp AR-205

    by johnbla
    Replies
    5
    Views
    1,004

    Need a bit more info on this... Single or...

    Need a bit more info on this...

    Single or Multiple pages ?
    Does the trailing edge p*ss the exit-gate from the Fuser?

    If Single page ~ Look at the exit Sensor and Arm.
    If not clear of the...
  24. Thread: AR 336

    by johnbla
    Replies
    7
    Views
    1,085

    P I C I, 22 - 1 Regards Johnbla ...

    P I C I, 22 - 1

    Regards

    Johnbla

    http://www.copierforum.co.uk
  25. Replies
    10
    Views
    2,598

    F1 indicates that there is a problem with the...

    F1 indicates that there is a problem with the Sorter attached to the Copier.
    If you hold down the 'Start' button another set of numbers will be displayed, that will inform you the exact area that is...
Results 1 to 25 of 74
Page 1 of 3 1 2 3